BOSCH GWS 7-100 T Professional Angle Grinder

4,050.00

Category: Tag:

Description

  • Model: GWS 7-100 T
  • Rated Power Input: 720 W
  • No-load Speed: 9300 rpm
  • Grinding Spindle Thread: M 10
  • Disc Diameter: 100 mm
  • Rubber backing pad, diameter: 100 mm
  • Wire cup brush, diameter: 70 mm
  • Weight: 1.8 kg

Features:

  1. 56 mm slim housing in round shape for super comfortable holding
  2. Powerful and robust 720 W motor
  3. High torque model with metal bearing flange, perfect for any tough applications

Why This Tool?

  • Dimple surface for anti-slip
  • Specially designed air inlets for optimal airflow and cooling
  • Small gear head for working in tight spaces
  • Gearhead can be rotated in 90° steps
  • Armoured coils that protect motor against sharp grinding dust for longer service life
  • Auto cut-off carbon brushes

Safety Warnings for Angle Grinder
Safety Warnings common for Grinding, Sanding,
Wire Brushing or Abrasive Cutting Off Operations

  • This power tool is intended to function as a grinder,
    sander, wire brush or cut-off tool. Read all safety warnings,
    instructions, illustrations and specifications provided
    with this power tool. Failure to follow all instructions
    listed below may result in electric shock, fire and/or
    serious injury.
  • Operations such as polishing are not recommended to
    be performed with this power tool. Operations for which
    the power tool was not designed may create a hazard and
    cause personal injury.
  • Do not use accessories which are not specifically designed
    and recommended by the tool manufacturer.
    Just because the accessory can be attached to your power
    tool, it does not assure safe operation.
  • The rated speed of the accessory must be at least equal
    to the maximum speed marked on the power tool. Accessories
    running faster than their rated speed can break
    and fly apart.
  • The outside diameter and the thickness of your accessory
    must be within the capacity rating of your power
    tool. Incorrectly sized accessories cannot be adequately
    guarded or controlled.
  • Threaded mounting of accessories must match the grinder
    spindle thread. For accessories mounted by flanges,
    the arbour hole of the accessory must fit the locating diameter
    of the flange. Accessories that do not match the
    mounting hardware of the power tool will run out of balance,
    vibrate excessively and may cause loss of control.
  • Do not use a damaged accessory. Before each use inspect
    the accessory such as abrasive wheels for chips
    and cracks, backing pad for cracks, tear or excess
    wear, wire brush for loose or cracked wires. If power
    tool or accessory is dropped, inspect for damage or install
    an undamaged accessory. After inspecting and installing
    an accessory, position yourself and bystanders
    away from the plane of the rotating accessory and run
    the power tool at maximum no-load speed for one minute.
    Damaged accessories will normally break apart during
    this test time.
  • Wear personal protective equipment. Depending on
    application, use face shield, safety goggles or safety
    glasses. As appropriate, wear dust mask, hearing protectors,
    gloves and shop apron capable of stopping
    small abrasive or workpiece fragments. The eye protection
    must be capable of stopping flying debris generated
    by various operations. The dust mask or respirator must be
    capable of filtrating particles generated by your operation.
    Prolonged exposure to high intensity noise may cause
    hearing loss.
  • Keep bystanders a safe distance away from work area.
    Anyone entering the work area must wear personal
    protective equipment. Fragments of workpiece or of a
    broken accessory may fly away and cause injury beyond
    immediate area of operation.
  • Hold the power tool by insulated gripping surfaces only,
    when performing an operation where the cutting accessory
    may contact hidden wiring or its own cord. Cutting
    accessory contacting a “live” wire may make exposed
    metal parts of the power tool “live” and could give the operator
    an electric shock.
  • Position the cord clear of the spinning accessory. If you
    lose control, the cord may be cut or snagged and your hand
    or arm may be pulled into the spinning wheel.
  • Never lay the power tool down until the accessory has
    come to a complete stop. The spinning wheel may grab
    the surface and pull the power tool out of your control.
  • Do not run the power tool while carrying it at your side.
    Accidental contact with the spinning accessory could snag
    your clothing, pulling the accessory into your body.
  • Regularly clean the power tool’s air vents. The motor’s fan
    will draw the dust inside the housing and excessive accumulation
    of powdered metal may cause electrical hazards.
  • Do not operate the power tool near flammable materials.
    Sparks could ignite these materials.
  • Do not use accessories that require liquid coolants. Using
    water or other liquid coolants may result in electrocution
    or shock.
    Kickback and related warnings
  • Kickback is a sudden reaction to a pinched or snagged rotating
    wheel, backing pad, brush or any other accessory.
    Pinching or snagging causes rapid stalling of the rotating accessory
    which in turn causes the uncontrolled power tool to
    be forced in the direction opposite of the accessory’s rotation
    at the point of the binding.
    For example, if an abrasive wheel is snagged or pinched by
    the workpiece, the edge of the wheel that is entering into the
    pinch point can dig into the surface of the material causing
    the wheel to climb out or kick out. The wheel may either
    jump toward or away from the operator, depending on the direction
    of the wheel’s movement at the point of pinching.
    Abrasive wheels may also break under these conditions.
    Kickback is the result of power tool misuse and/or incorrect
    operating procedures or conditions and can be avoided by
    taking proper precautions as given below.
  • Maintain a firm grip on the power tool and position your
    body and arm to allow you to resist kickback forces. Always
    use the auxiliary handle, if provided, for maximum
    control over kickback or torque reaction during
    start-up. The operator can control torque reactions or
    kickback forces if proper precautions are taken.
  • Never place your hand near the rotating accessory. The accessory
    may kickback over your hand.
  • Do not position your body in the area where power tool
    will move if kickback occurs. Kickback will propel the
    tool in a direction opposite to the wheel’s movement at the
    point of snagging.
  • Use special care when working corners, sharp edges,
    etc. Avoid bouncing and snagging the accessory. Corners,
    sharp edges or bouncing have a tendency to snag the
    rotating accessory and cause loss of control or kickback.

Bosch Heavy Duty
Bosch Heavy Duty – Power, Performance, and Robustness redefined!

 
Direct cooling

Direct cooling
For high overload capability and a long service life.

 
Outstanding user protection

Outstanding user protection
thanks to the anti-rotation protective guard – stands firm, even if the disc breaks

 
Comfortable handling

Comfortable handling
of the tool thanks to soft grip

 

 

Reviews

There are no reviews yet.

Be the first to review “BOSCH GWS 7-100 T Professional Angle Grinder”

Your email address will not be published. Required fields are marked *

10 − 2 =